Multi-line 2 Utility Software v.3.x. 3.52.0

3.52.0

22/02/2022

USW3 build version: 2123.
USW3 product database revision: 7880.

New features:

• Added Support for IEEE 1547 on selected controllers.
• Added fields to Identifiers window to meet dataplate requirements of IEEE 1547.
• Added configuration parameters and their graphical representation on the Advanced Protections page.
• Added parameter validation to meet the configuration requirements of IEEE 1547.

Changes:

• Changed graph component to support new features and requirements.
• Changed spinedit component to support new features and requirements.
• Identifiers window content is now always read when opening the window.
• Identifiers window now asks for confirmation when it is being closed.

Corrections:

• Fixed an issue causing the Inverter Data page to freeze when opening.
• Fixed an issue where the slider value would work irregularly.
• Fixed an issue that caused a crash when the IP address was not available.
• Fixed an issue for an illegal data value error when writing Multi-Inputs.
• Fixed an issue that caused the language selection to not be available.
• Fixed an issue where setpoint 3 was not available for RMI inputs.

3.62.1 PDB 11714

09/07/2025

USW3 build revision: 3169
USW3 product database revision: 11714

Updates

• Updated support for new controller firmware for iE 150 – 1.33.0
• Updated support for new controller firmware for AGC-4 Mk II - 6.22.0

3.62.1

10/06/2025

USW3 build revision: 3169
USW3 product database revision: 11593

Corrections

• Resolved crash when using certain keywords in search.
• Fixed issue where generators could disappear from the application.
• Addressed drag-and-drop issues in M-Logic.
• Restored missing translations on AGC-4 Mk I, ALC-4, ASC-4 and AGC 5C.
• Fixed collapsed tags in the trending view.
• Resolved crash when using filters in the AOP logic drop-down.
• Fixed issue where M-Logic content disappeared when filtering and using move line up/down.

3.62.0 PDB 11519

09/05/2025

USW3 build revision: 3151
USW3 product database revision: 11519

New features & improvements

• Moved display views configuration to a dedicated page.    
• Introduced a third party integration page and dedicated IO page.
• Added advanced filtering capabilities, including EIC Viewline and tag-based filters.

Corrections

• Improved page behavior for data persistency and automatic data read.
• Standardized behavior when switching between pages.
• Fixed crash when changing password level.
• Resolved issues with data tracer and parameters tree view
• Restored visibility of M-Logic from older ECU 100 controllers.
• Corrected source measurement updates in plant control.
• Fixed permission handling for digital outputs in AGC 150/iE 150 setups.
• Ensured 'start engine' command is visible in application supervision.
• Resolved missing options in the batch file interface.

3.61.0 PDB 11353

10/03/2025

New features

• Added support for AGC-4 Mk II - 6.20.0.

3.61.0

07/02/2025

This update brings new scheduler functionality, significant improvement to comparison tool, support for iE 150 Marine, along with improvements and bug fixes that enhance software stability and performance.

New features

• Comparison tools have been updated with more compare functions.
• M-Logic search function has been improved including descriptions and faster clearing speed.
• Support for iE 150 Marine variants.
• Live values enhancements.
• New Scheduler page.

Corrections

• Added confirmation message when I/O settings are written successfully.
• Resolved access violation errors in configuration, plant emulation and file comparison.
• Fixed configuration issues with CIO 208 modules 4 and 5.
• Corrected batch write issues in combined engine and network configuration.
• Fixed AGC 150 translation prompt issue due to version mismatch.
• Application supervision now shows correct status for active PV.
• Restored missing BTB redundant option for AGC-4 Mk II.
• Fixed special character corruption in translations.
• Resolved translation read issue.
• Fixed "Save All" function in USW 3.60.2.
• Corrected software revision in identifiers.
• Resolved incorrect Inhibit settings.
• Resolved project closing issues in Advanced Protection/ECU & DAVR configuration.
• Updated footer connect name display.

3.60.2

09/01/2025

USW3 build version: 2983
USW3 product database revision: 11101

New features

• Support of AGC 150 – 1.22.0.
• Support of AGC-4 Mk II - 6.15.0.
• Support of ASC-4 - 4.29.0.

3.60.2

15/10/2024

USW3 build version: 2983
USW3 product database revision: 10963

New features

• Support of AGC 150 – 1.21.0.
• Improved application supervision in USW-3 for iE 250 systems.

3.60.2

02/10/2024

USW3 build version: 2983
USW3 product database revision: 10901.

New features

• Support of AGC-4 Mk II – 6.14.0

3.60.2

19/09/2024

USW3 build revision: 2983
USW3 product database revision: 10810

Improvements

• Enhanced the graph to support improved dragging and scrolling for better usability.
• Refined the display of the live bus bar within the USW application supervision for more accurate monitoring.
• Updated the supervision page to enable proper command functionality when solar is added to load points.
• Extended compatibility for Ring busbar configurations to ensure support across legacy PMS IDs for ASC-4 and ASC 150 systems.
• Enhanced translation encoding when writing to AGC 150 controllers for better text accuracy.
• Adjusted the layout to prevent overlapping measurement data when PV / Battery is added to the load point.
• Improved compatibility and consistency across M-Logic versions.
• Refined the handling of modified command register addresses for improved system response.
• Streamlined the AGC 150 firmware upgrade process to reduce delays.

Correction

• Corrected symbol display on the PPM-3 Shore device page when using offline files.

3.60.1

09/07/2024

USW3 build version: 2925.
USW3 product database revision: 10688.

New features

• Support of AGC 150 version 1.20.0.

3.60.1

24/06/2024

USW3 build revision: 2925

USW3 product database revision: 10644

Corrections

  •  Improved the functionality of the "Write to all" parameter.
  •  Ensured compatibility for parameter files between USW 3.59.1 and 3.60.0.
  •  Fixed an issue with the storage of some translation texts in controllers.
  •  Verified and tested batch job stability for CIO in AGC 4 MK I.

Changes

  •  Implemented handling for missing Cio.xml files in ASC-4 Battery controllers and others.

3.60.0

03/06/2024

USW3 build revision: 2912

USW3 product database revision: 10488

New Features

 • New way of handling translations.
 • Search Function & Description in M-Logic.
 • Live value on USW pages.
 • Live value on ECU & D-AVR pages.

  
Improvements

 • Improved handling of Power Meter & Inverter Data
 • Enabling AOP2 based on software package.

  
Corrections

 • 'Access Violation' error when trying to change the password level.
 • M logic & AOP Print option enabled.
 • Menu text overlapping.
 • Access violation.t.

3.59.1

04/04/2024

USW3 build revision: 2851

USW3 product database revision: 10229

Corrections

• Correction to permissions write during batch write.
• AOP-2 emulated button corrected.
• M-Logic delay timer was not written to the controller.
• M-Logic items in use showing wrong counting.
• M-Logic and AOP in use button not showing active M-Logic lines with offline files.
• M-Logic and AOP in use button showing wrong interpretation for Virtual event output.

3.59.0

12/02/2024

USW3 build revision: 2814

USW3 product database revision: 10079

New features

• Added separate page for ECU and DVC configuration.

Improvements

USW performance improvements:

• M-Logic & AOP handling.
• .Trend file handling.
• Parameter tree structure.
• Alarm update in USW.
• USW message pop-up.
• Batch read and write.
• Offline file handling.

3.58.0

22/12/2023

USW3 build revision: 2752

USW3 product database revision: 9675

New features

• Added support for AGC 150 – 1.18.0.
• Added support for ASC-4 – 4.27.0.
• Added support for AGC-4 Mk II – 6.12.0.

3.58.0

22/09/2023

USW3 build revision: 2752

USW3 product database revision: 9374

New features

• Added data logging status.
• Added dynamic table for PMS lite application supervision.
• Dynamic parameter based on configurational value to show relevant parameters.

Corrections

• Improved batch write function.
• Fixed translation issues.
• Fixed issue with opening general purpose PID.

3.57.1

07/09/2023

USW3 build revision: 2715

USW3 product database revision: 9215

Corrections

•  Batch read and write fixed
• Other bugs fixed

3.57.0

10/07/2023

USW3 build version: 2686

USW3 product database revision: 9157

New features

• Added offline configuration comparison tool.
• Added new device page for PMS Lite.
• Added new application supervision for PMS Lite.
• Added option to open and save sensor curve file in AGC 150 Engine drive, AGC 150 Engine drive marine, AGC 150 Generator marine, AGC 4 Mk II Genset.

Corrections

• Fixed access violation error when function keys F4 and F5 are pushed too quickly.

3.56.0

27/02/2023

USW3 build version: 2516

USW3 product database revision: 8789

New features

• Live value available from the "Parameters" page in tree view mode.
• New translation files are added to the translation folder.

Changes

• Moved "Permissions" icon to the left menu under "Tools". It is still called "Permissions".
• Moved "PID Configuration" icon to the left menu under "Tools". Renamed to "General Purpose PID”.
• Moved "Modbus Configuration" icon to the left menu under "Tools". The name is the same.
• Added "Firmware" to the "Option" page. Renamed "Option" to "Option & firmware”.
• "Device Information" is now available from the "Option & firmware" page.
• Optimised the tree view text.
• Moved "N-Option" icon to the left menu under "Tools". Renamed to "Ethernet Setting (Modbus TCP/IP)".
• Changed "Open & Close" hyperlink to button icon.
• Changed the maximum number of languages for AGC 150 to 8.
• Moved "Translations" from "Configuration" to "Tools".

Corrections

• Optimised the menu bars and windows.
• Optimised the connection with the controller.
• Fixed "Write to plant" function.
• Fixed sensor scaling and curve for multi-input AGC 150 DG.

3.55.1

09/01/2023

USW-3 build version: 2457
USW-3 product database revision: 8666

New features

• Selective reading/writing of M-Logic and AOP.
• CIO configuration moved from pop-up to a dedicated page.
• Parameter tree view improvements:
  • Collapsible panels
  • Search function
  • Parameter number
  • Tree structure improved
• New pop-up for disconnect function.
• Support of 5 CIO 308 modules for AGC-4 Mk II.
• Support of 5 CIO 208 modules for AGC-4 Mk II.
• Support of 5 CIO 116 modules for AGC-4 Mk II.
• Multi-input: Added selection for the number of points in the configurable sensor curve.
• Multi-input: Changed open & close text hyperlink to button.
• Translation folder created in app data location with language files.

Changes

• Updated sensor files.

Corrections

• Every time advanced protection parameters are read, the USW reports that the connection timed out.
• Question marks in I/O setup from old controller.
• USW disconnects when another power management unit is missing.
• Code ANSI zero sequence current/voltage corrected in mouse-over text for parameters.
  
  

3.54.1

21/10/2022

USW3 build version: 2362
USW3 product database revision: 8516

Changes:

- USW Connection Handling.
- Sensor curve open & close hyperlink text colour.
- RMI Type Selection in multi-input available again.

Corrections:

- Enhanced performance for "Inverterdata".
- AGC-4 Mk II function drop-down disabled for breaker feedback.
- RMI Scaling in multi-input fixed.

3.54.0

09/09/2022

USW3 build version: 2320.
USW3 product database revision: 8363.

New features:

• Support of AGC 150 – 1.12.0
• Support of ASC-4 – 4.23.0

3.54.0

29/08/2022

USW3 build version: 2320
USW3 product database revision: 8322

New Feature

• Added provision to edit and save sensor curves for multi Inputs and CIO
• Added pre-defined sensor curve
• New launcher window

Changes

• Left-side navigation menu style
• Change symbol in USW

Corrections

• Batch write crash issue.
• Russian language.
• USB driver signing issue.
• M-logic will overwrite other saved items

3.53.0

30/06/2022

USW3 build version: 2186.
USW3 product database revision: 8174.

Changes:

• Support of AGC 150 – 1.11.0
• Support of ASC-4 – 4.22.0
• Support of AGC-4 Mk II – 6.07.0
• New Launcher page for selected products.
• New Menu bar for selected products.
• Ability to save and load sensors via customer files

3.53.0

25/04/2022

USW3 build version: 2186

USW3 product database revision: 7957

New features:

• Added Portuguese (Brazil) localization.
• Reduced repeated lists on the Product Database.
• Button to open/close the M-Logic toolbox.

Changes:

• New ProductIDs in USW V.3.53.0.
• Russian language for Views.

Corrections:

• USW crashing with Floating-point overflow.
• Expand buttons disappear when using "Copy to the line below" (AGC 4 and AGC150).
• Mismatch column in parameter tab is not present corrections.
• Parameter disappears after changing Parameter 7841.
• Spinedit component resolution does not respect the decimals attribute.

3.52.0

22/02/2022

USW3 build version: 2123.
USW3 product database revision: 7880.

New features:

• Added Support for IEEE 1547 on selected controllers.
• Added fields to Identifiers window to meet dataplate requirements of IEEE 1547.
• Added configuration parameters and their graphical representation on the Advanced Protections page.
• Added parameter validation to meet the configuration requirements of IEEE 1547.

Changes:

• Changed graph component to support new features and requirements.
• Changed spinedit component to support new features and requirements.
• Identifiers window content is now always read when opening the window.
• Identifiers window now asks for confirmation when it is being closed.

Corrections:

• Fixed an issue causing the Inverter Data page to freeze when opening.
• Fixed an issue where the slider value would work irregularly.
• Fixed an issue that caused a crash when the IP address was not available.
• Fixed an issue for an illegal data value error when writing Multi-Inputs.
• Fixed an issue that caused the language selection to not be available.
• Fixed an issue where setpoint 3 was not available for RMI inputs.

3.51.0

16/02/2022

USW3 build version: 1978.
USW3 product database revision: 7845.

New features:

• Support of AGC 150 – 1.10.0
• Support of ASC-4 – 4.21.0
• Support of AGC-4 Mk II – 6.06.0

3.51.0

16/12/2021

USW3 build version: 1978.
USW3 product database revision: 7679.

New features:

• Support of AGC 150 – 1.09.0
• Support of ASC-4 – 4.20.0

3.51.0

11/11/2021

USW3 build version: 1978.
USW3 product database revision: 7621.

New features:

• Support for PMS redundancy on AGC 150.
• Support for AGC 150 Remote Display variant.
• Support for AGC 150 Marine.

Changes:

• The device page for AGC 150 Hybrid now shows values for the inverter.
• The supervision page for AGC 150 Hybrid now shows a generator with a PV panel.

Corrections:

• Solves an issue that made it difficult to edit numeric fields.
• Solves an issue that made toolbars seem to not be present.
• Solves an issue that caused corruption to special characters on export of Translations to a CSV file.
• Solves an issue on I/O Setup occurring when opening a .usw file of AGC 150 and AGC-4 Mk II.
• Solves reported issues of support for special character handling in several pages.
• Solves an issue leading to errors in the graphs of the VRT tabs in Advanced Protections.

3.50.1

07/07/2021

USW3 build version: 1880
USW3 product database revision: 7366

Corrections:

• Fixed an issue that prevented users from scaling the multi-inputs.

3.50.0

09/06/2021

USW3 build version: 1849
USW3 product database revision: 7312

Changes:

• Validation of CIO 208 configuration written to the controller
  
  • In some cases, the controller may reject the configuration set by the user.
  • The Write function now reads back from the controller and notifies the user in case of disparity between the user selections and the controller.

Corrections:

• Fixed an issue causing failures to read the CIO configuration in Batch Read.
• Fixed an issue where some drivers had a wrong digital signature.
• Fixed an issue where multi-input scaling would change back to "DegC 1/1" after writing to the controller.
• Fixed an issue where Batch Read and Batch Write would not work properly for Multi-input settings.
• Fixed an issue where the RMI configuration would be lost when using the Batch Write functionality.
• Fixed an issue where the Batch job would finish but the pop-up would not accurately depict the progress.
• Other small fixes and performance improvements.

3.47.2

28/04/2021

USW3 build version: 1808.
USW3 product database revision: 7240.

What's new:

Support of AGC150 – 1.06.0.

New features:

• Added AGC150 Engine drive variant.
• Added fallback timer for power limit on SunSpec (parameter 17180).
• Added support for Keyswitch in I/O setup.
• Added support of PV breaker.
• Added EIC and MPU speed to delta alarms.

3.47.2

25/03/2021

USW3 build version: 1808.
USW3 product database revision: 7181.

What's new:

Support of AGC-4 – 4.81.0
Support of AGC-4 Mk II – 6.02.0
Support of ASC-4 – 4.16.0

Corrections:

• Solves an issue where importing favorites was not working.
• Solves an issue where errors would occur when the PC awakes from sleep mode.
• Solves an issue where the parameters from Advanced Protections would not be consistently written to the controller.
• Solves an issue where AOP 1 and AOP 2 would be written when cancelling the write operation of M-Logic.
• Solves an issue where an Access Violation error would occur when writing to multiple controllers.
• Solves an issue where the "Enable" parameter was not written when writing to multiple controllers.
• Solves an issue where the IP address would disappear from the bottom status line on some controller types.
• Solves an issue where the CIO 116 and CIO 208 could not be configured.
• Solves an issue where an error would occur when selecting CIO 116 on some controllers types.

3.47.1

12/01/2021

USW3 build version: 1743.
USW3 product database revision: 6991.

What's new:

  • AGC-4 Mk II release:
  • Support for Application SW download.
  • New bootloader available for AGC-4 Mk II.

  • New I/O setup page for AGC 150 and AGC-4 Mk II:
  • The I/O configuration toolbar button and respective page have been deprecated for the mentioned products.
  • The input alarm and relay configuration functions have been removed from the parameter list for the mentioned products.
  • Digital input and multi-input functions and alarms are now placed in tabs on the I/O setup page, accessible from the main navigation menu on the right side of the window.
  • Output functions and configuration are now placed in a single tab on the I/O setup page.

  • CIO input/output function setup:
  • Due to the removal of the I/O configuration pop-up, CIO116 and CIO208 functions can be selected in the CIO configuration page.
  • The support for functions on CIO308 multi-inputs is not supported by this release.

3.45.4

03/09/2020

USW3 build version: 1518
USW3 product database revision: 6586

What's new:

• Adds support of upcoming AGC 150 Hybrid.
• Adds support of upcoming AGC-4 version 4.79.0.
• Adds support of upcoming ASC-4 version 4.14.0.

Corrections:

• Solved issue with CIO alarm setpoint shown as zero.
• Solved issue where AGC 150 multi input alarm delays were possible to set outside the allowed range.

3.45.3

27/03/2020

USW3 build version: 1490
USW3 product database revision: 6360

New:

• Adds support of upcoming AGC 150 version 1.02.0.
• Adds support of upcoming AGC 150 version 1.03.0.
• Adds support of upcoming AGC-4 version 4.77.0.
• Adds support of upcoming ASC-4 version 4.12.0.

3.45.2

17/12/2019

USW3 build version: 1471
USW3 product database revision: 6257

New:

• Adds support of upcoming AGC-4 version 4.75.0.
• Adds support of upcoming AGC-4 version 4.76.0.
• Adds support of upcoming ALC-4 version 4.10.0.
• Adds support of upcoming AGC 150 version 1.01.0.

Corrections:

• Solves an issue where the Multi Input alarm inhibits from a stored usw-file, was changed to zero before written to the AGC 150.
• Solves an issue with wrong scaling on Multi Input: Alarm Set points for input types: PT100 and RMI Fuel level
• Solves an issue with wrong scaling on Multi Input: Curve Set points for input type = RMI Water temp.

3.45.1

29/08/2019

USW3 build version: 1439
USW3 product database revision: 6109

Corrections:

• Solves an issue where the firmware could not be downloaded to the AGC 150 via TCP/IP if the PC and the controller were not on the same subnet. 
• Solves an issue with wrong scaling on droop curve 2 parameters.

3.45.0

06/05/2019

USW3 build version: 1430
USW3 product database revision: 6024

New Features:

• Support for configurable 5 line display view in AGC 150 series. 
• Support for AGC 150.
  - Firmware update USB and LAN
  - Bootloader update
  - New Multi-Input setup page
  - New Navigation icons

• Support of ASC-4 Load Point connection in Power Management applications. 

Improvements:

• Commissioning view in Parameter removed when irrelevant to parameter 
• Trending settings are now allowed to be down to 20 ms (0.02s) polling.  
    - Note: Controller may not be able to deliver data at this rate.

Corrections:

• Solves an issue where the Log page would no read all log lines. 
• Solves an issue where plant read/write would fail in some occasions. 
• Fixes the command line parameter for Advanced protections. 
• Solves an issue introduced in USW v.3.44.0 where the "M-Logic and AOP items in use" window would not show all information. 
• Solves an issue where parameters could be missing in the batch (.usw) file. 
• Solves an issue introduced in USW v.3.44.0 where the AOP2 configuration could fail. 
• Solves an issue where Beckhoff modules outputs were missing on the GC-1F. 
• Solves an issue where the ASW is not shown when writing batch file on the AGC100. 
• Fixes the battery colour in Application Supervision. 

3.44.1

21/01/2019

USW3 build version: 1386
USW3 product database revision: 5778

Corrections

1. Advance protection Print and print preview 
2. Power management now showing in M-Logic & AOP Events
3. M-Logic offline file can be opened without connecting to controller
4. Sequence CIO and PID has been changed while batch writing 

3.44.0

06/12/2018

USW3 build version: 1372
USW3 product database revision: 5733

New Features:

• M-Logic & AOP
   - M-Logic and AOP configuration are now organised in tabs on the same page.
   - The AOP configuration pop-up is changed to work as an AOP mimic (ASW > 4.60.0).
   - Added a visual representation (diagram) of the logic blocks selected in the logic line.
   - Added a toolbar for easy drag-and-drop of Events and Outputs to the logic lines.
   - Dynamic M-Logic and AOP are now evaluated on the logic lines diagram.   
• Parameters - Sets of Favourites
   - Users can create/modify/delete sets of Favourites under the Settings page.
   - Users may Import/Export Favourites sets in settings under the Settings page.
   - Users can categorise parameters into different sets of Favourites.
   - Favourites filter has now a drop-down menu for selecting from the available sets of Favourites.
• Parameters – Parameter management
   - Users can now perform selective saving and writing of parameters.
   - A new indicator help users to identify parameters that were edited, but not written.
   - Users can now filtrate the parameter list for edited parameters.
• Advanced Protections configuration page for options A1, A10, C2 (ASW > 4.70.0)
• Command line 
   - It is now possible to merge parameter files with the command line interface.
   - Merged parameters can be written to a file or written directly to a controller.

Improvements

• USW is now an available application to select from on Windows side-by-side view.
• ALCs can now be added to the left of Mains.
• Performance improvements in reading parameters (after first read). 

Corrections

• Fix for batch read/write and backup/restore for PID settings and ID.
• M-Logic not displayed in USW3 under content in .usw file

3.43.2

27/09/2018

USW3 build version: 1236
USW3 product database revision: 5599

New

• Adds support of upcoming AGC-4 version 4.68.0.
• Adds support of upcoming AGC 200 version 4.68.0

3.43.2

12/06/2018

USW3 build version: 1236
USW3 product database revision: 5477

New

• Adds support to the upcoming release of ASC-4.11.0
• Adds support to the upcoming release of AGC-4.67.0

Improvements

• Changes the naming of output tab in parameters to ‘Outputs’

Fixes

• Fixes an issue in AGC 200 M-Logic where Ventilation mode and Dry mode were not working.

3.43.2

15/05/2018

USW3 build version: 1236
USW3 product database revision: 5368

Corrections:

• In some cases where the OS was localised, the utility software was wrongly showing a debug version message.

3.43.1

16/03/2018

USW3 build version: 1222
USW3 product database revision: 5368

New features:

• QR code for options upgrade
• Visual updates in application supervision
• Command buttons for DG units in supervision
• Click on unit to open its command panel
• Up to 8 configurable values may be added for each ID in supervision (only units configured on top or bottom of area)
• Sorting I/O in alphabetical order
• Duration of mouse-over texts is now configurable
• USW now stores the parameter view settings so that it opens in same view next time
• Support of AGC-4 version 4.66.0
• Support of ASC-4 battery controller

Changes:

• Various updates related to ALC-4
• Various updates related to ASC-4 PV

Corrections:

• In some situations, the USW would not show the correct application and breaker positions
• ASC Battery: When drawing a stand-alone application for ASC Battery with only the battery, the colours are wrong

3.42.0

12/10/2017

USW3 build version: 1164
USW3 product database revision: 5223

New features:

• Support of AGC-4 and AGC 200 version 4.65.0
• Support of new power meters on ASC-4

Corrections:

• Corrected: AGC 233 parameters not shown
• Corrected: Emulation in AGC 200 and AGC-4 not working

3.42.0

01/09/2017

USW3 build version: 1164 
USW3 product database revision: 5181

New features:

• Radio Ripple Control Receiver (RRCR) communication support for ASC-4/ASC PM
• Option N will create exceptions for firewall, but only if the user is admin. This will be handled in the installation file
• Includes reliability data in USW files
• Dynamic evaluation added to AOP-1 and AOP-2
• Navigation in the USW even when AOP window is open
• Text representing the regulator mode
• "Save All" files function on the USW
• Support of new ID configuration
• Shows SIPC number in USW3 when USW is built/used for an SIPC
• Possible to zoom in and out in the plant view
• Support of digital I/O in trending
• Support of trend only mode

Changes:

• Inverter data support updated for ASC-4, ASC PM
• Improved dialogue when changing between units 
• Application supervision unit ID on PV and LG
• CIO inputs column in the Inputs/Outputs list is made wider
• Possible to multiply the trending values so they match the CIO configuration

Corrections:

• Strange pop-up during connection to a genset group tie removed (build 1092)
• CIO added to OEM product IDs
• Unconfigured TB is no longer shown
• Corrected: Remote maintenance M-Logic missing (option H12)
• Translation no longer reveals passwords
• Option H13 added in option overview
• MB is no longer shown when opening a batch file when it is not present
• List of CIO 308 cold junction inputs is now updated when reconnecting the USW
• Unit scaling and RMI sensor type are aligned 
• Russian translation of RMI corrected
• "Active alarm log" can be pulled up again after minimising
• Dialogue box no longer keeps the existing M-Logic text
• M-Logic no longer disappears during batch reading
• AGC 100: Writing phone numbers with a batch write no longer results in strange characters
• Possible to write CIO parameters with batch file
• BTBs can no longer be misplaced in application drawings with ASC/ALC
• Power management ID selection logic corrected, when using new IDs
• M-Logic event C drop-down list now always opens
• Logged alarm values are now scaled correctly

3.41.2

03/04/2017

USW3 build version: 1119
USW3 product database revision: 4980

New features:

• Support of AGC 222 OEM variant

3.41.0

25/11/2016

This software applies to the following DEIF products:

• GC-1F v.1.xx
• Multi-line 2 - AGC v.3.xx
• Multi-line 2 - PPM v.3.xx
• Multi-line 2 - PPU v.3.xx
• Multi-line 2 - GPU v.3.xx
• Multi-line 2 - GPC v.3.xx
• Multi-line 2 - AGC 200
• GC-1F ATS
• GC-1F/2 v.2.xx
• Multi-line 2 - AGC v.4.xx
• Multi-line 2 - GPU-3 REC ver. 3.xx
• Multi-line 2 - AGC 100 v. 4.xx
• Multi-line 2 - CGC 200
• Multi-line 2 - CGC 400
• Multi-line 2 - ECU 100
• Multi-line 2 - GCU 100
• Multi-line 2 - PPU v.3.xx Marine
• Multi-line 2 - GPU v.3.xx Marine
• USW3 build version: 1056
• USW3 product database revision: 4805

Changes:

• Additional product database updated to support AGC-4 v.4.59.0.
• Alarm set point range of CIO 308 Pt100/Pt1000 inputs extended.
• Please note: Only the configuration files have changed.

New features:

• Support of CIO 116, CIO 208 and CIO 308
• Support of ALC-4 and ASC-4

Changes:

• Serial number made mandatory, in the option key generator.
• Product database updated to support AGC-4 v4.59.0
• Product database updated to support AGC 200 v4.59.0

Corrections:

• Voltmeter on device page corrected
• Buttons placed correctly in tree view
• AGC 100 "Counters and identifiers" issue corrected
• Various corrections to option N software

3.40.1

06/07/2016

40.1 06-07-2016

Changes:

• 1- Product database updated to support AGC-4 v4.57.0
• 2- Product database updated to support AGC 200 v4.57.0
• Please note: Only the configuration files have changed...
• 3.40.1 06-06-2016

Changes:

• Product database updated to support ASC PM Solar v5.06.0
• 3.40.1 31-05-2016

Changes:

• Product database updated to support AGC-4 v4.56.0
• Product database updated to support CGC 412 and CGC 413 v1.13.1
• Minor product database updates to AGC 252
• 3.40.1 21-12-2015 Changes:
• Added support for AGC 252

Corrections:

• PPM-3: In USW application configuration, two EDGs could be drawn, while only one EDG is supported in an application.
• Please note: Only the configuration files have changed...
  3.40.1 27-11-2015 

Changes:

• Updated Product Database for various products
• 3.40.1 01-07-2015 Corrections:
• USW 3.40 - F3 connection menu is not working for new users

3.40.0

24/06/2015

New features:

• Support of AFC PM (Automatic Fuel Controller).
• Support for Windows 8 - language selection.
• Support for 1/10000 in units.
• Translation tree. 

Changes:

• CAN line names - use of primary and secondary instead of A and B.
• Grey out of button for “activate plant configuration”, if only single unit application. 

Corrections:

• Russian language causes PDF export to fail.
• Parameter texts on shared channels updated correctly.
• Missing “edit notification” in list view, after parameter change in tree view.
• Translation issues for CGC 400, AGC 100 products.
• Missing connect icon in emulation mode.
• Digital status page not updated correctly.
• TB missing in USW 3.39.0 application supervision.
• GC-1F/2 ASW 2.31.1 Application configuration should not be visible.
• AGC-3 Dual mains application configuration is not working.
• TB appearing in old application drawing when shown in newer USW version.
• Batch read from M-Logic tab not successful.
• IP address – leading zeros.
• Chinese M-Logic PDF export.
• MB present when none is configured.
• AGC 100 emulation option problem.
• Import translation from file.

3.39.0

19/09/2014

Re-location of USW 3.39.0 - link to NTP-patch included

3.39.0 26-09-2014 NTP patch for USW 3.39.0

A patch is needed to make the NTP-configuration work.

In future releases this won’t be necessary.

3.39.0 26-09-2014 NTP patch for USW 3.39.0

A patch is needed to make the NTP-configuration work.

In future releases this won’t be necessary.

3.39.0 26-09-2014 Re-location of USW 3.39.0 - inclusive link to NTP-patch. 

New features:

• Support of ASC PM (Automatic Solar Controller).
• Support of Qc1103. 
• Support for firmware download to webarm hardware with new flashes mounted.
• Support for configuration of NTP in webarm from ver. 2.40.0.

 Changes:

• Possibility to change Loginfo scaling factor.
• Change of bit mask when writing inhibit configuration to device.

 Corrections:

• Access level update
• CGC 400 - missing Russian letters for translation 
• Russian language support now working 100%
• USW 3.38 usw files not recognised by Windows.
• PPM-3 cannot open batch files "File format error"

3.38.0

11/06/2014

New features:

• Update boot SW (Standard ML2 ver. 3 products)

Corrections:

• PPM-3 display of power measurement
• USW 3.37.0 freezes when connecting to PPM unit
• CGC 200: default parameters available before reading from device
• CGC 200: Parameter editor - dropdown list value selection

3.37.0

01/04/2014

New features:

• Support for extended Chinese characters in CGC 400
• Support of AGC PM product

Changes:

• Scaling in Trending - Default setup and possibility to choose alternative 

3.36.0

23/12/2013

New features:

• Parameters: Tree view for AGC 100 variants
• Parameters: Reloading of dependent parameters for AGC 100 variants
• Support of firmware upgrading over a TCP-IP connection if the AGC-4 is version 4.40, the option N has version 2.20 and the boot code has version 1.03.0
• Communication: Faster communication over TCP-IP if the option N has version 2.20
• Communication: Network parameter pop-up to easily set the IP address, netmask and gateway if the AGC-4 is version 4.40 and the option N is version 2.20
• Logs: Support of up to 500 alarms and event log lines
• Views: Tree view of the Views items
• Identifiers: Display of boot code and option N firmware version
• Identifiers: Display of production info like serial number, order number and production date

Corrections:

• Faster communication over USB when a parameter pop-up is open

3.35.0

30/08/2013

New features:

• Project Properties: Store user-defined comments as part of usw file 
• Project Properties: Display the firmware version from which the different components inside the usw file originate 
• Alarms: Double-click an alarm and open the corresponding parameter 
• Parameters: Alarm status is updated while a parameter popup is open 
• Parameters: Simultaneous display of multiple parameter popups 
• Parameters: Export/import of the list of favorite parameters 
• Parameters: Inhibits column added to the list view 
• Parameters: Favorite and Modified-Parameter filters work in tree view as well (AGC-4 and AGC 200) 
• Parameters: Reloading of dependent parameters (AGC-4 and AGC 200)
• Parameters: For selected parameters the Output A & B values are shown in the tree view mode (AGC-4 and AGC 200)
• Parameters: Display the parameters for the AGC 200 in a tree-like structure 
• Logs: Open .sdl files originating from the flashcard in AGC 200 
• New USB driver for CGC 200 and CGC 400 variants. 

Corrections:

• The application retrieved during the initial connection to GCU 112 does not cause an error message
• Identifier texts with Unicode characters are not written correctly to AGC 200 products

3.34.1

08/05/2013

Corrections:

• The firmware flashing of the CGC 200 works on all PCs
• Scaling is working correctly for controllers configured to different power and voltage scalings
• Cos phi is removed from the Electrical data window for PPM controllers
• The apparent power (S) in the Electrical data window is correct for PPM controllers
• The offline Batch-read procedure is working correctly
• The data fields in the Electrical data no longer appear to be editable

3.34.0

20/03/2013

New features:

• Support of the CGC 200 and CGC 400 variants
• Support of the AGC 100 variants
• Support of the AGC 200 firmware 4.21
• Support of the ECU 100 and GCU 100 variants
• Install script updated:
  a) shows EULA
  b) displays the USB installation popups sequentially
  c) CGC 200 USB driver added
• Supervision: Display of all available electrical data for the controllers in the application
• Supervision: Emulation support in a broad range of products (AGC 100, AGC 200 firmware >= 4.21,ECU and GCU 100 variants)
• Supervision: Save a screen copy to a graphical file 
• Supervision: Plant settings popup for easy access to parameters often changed after commissioning (applies only for AGC-4 and AGC 200 variants)
• Parameters: Display of parameters in a tree-like structure (applies only for AGC-4 variants and CGC 200)
• Alarms: Acknowledge of alarms individually
• Chinese localisation

Changes:

• Connecting to device procedure is more intuitive
• Alarms: Display of current alarms and alarm history

Corrections:

• The writing of Translations has been improved
• M-Logic and AOP lines have a consistent numbering in the relevant popups
• Read logs from GC-1F no longer fail

3.33.0

09/10/2012

New features

• Support of redundancy (AGC-4 only)
• Indication of the parameters that have been changed since commissioning (AGC-4 only)
• Display in Appl. Supervision of the names assigned to engines, breakers and mains (AGC-4 only)
• Possibility to reset logs in the controller (AGC-4 and AGC 200 only)

Changes

• M-logic page is empty initially
• M-Logic page adjusts to the width of the window
• Device page can handle negative power values

Corrections

• Batch write issue regarding Modbus configurator data was fixed
• Application Configuration page does not show “AGC” in the header initially
• Service level user can change the access level of any parameter to any lower level
• Data tracer will show the same number of digits as in the Trending window

3.32.0

07/06/2012

Install script updated to remove temporary files, which can cause problems during installation 

New features:

• The Connect Symbols are shown in Application Supervision to indicate the connected controller
• The texts assigned to digital inputs are shown in the Emulation inside Application Supervision
• Printout of Engine and Genset data in Application Supervision
• Applications are presented in tabs in Application Configuration
• Improved user interface to perform activation and broadcasts of applications
• Customisation of column widths in Parameter and Translations pages
• Execution of selected functions at the Windows Command prompt
• Automatic adjustment to the baud rate of the controller
• Faster batch writing of languages as those not translated are skipped
• Parameters can be tagged as favorites and a favorite filtering in the Parameter list can be applied
• The access level can be changed for a selected list of parameters
• Which columns to show and the sequence of these can be customised in the Parameters page
• Only enabled M-logic lines are shown on printouts
• Counter and Identifiers information can be printed

Changes:

• Properties of the following products were updated: AGC-3, AGC 200, PPM-3, AGC-4, GC-1F/2, PPU-3, PPM-3, GPU-3, GPC-3, GPU-3 REC, APU 264

Corrections:

• For the PPM-3 the terminal numbers given in the I/O page are correct
• Only Modbus ids in the range 1..247 are allowed
• Various improvements in the Color Scheme Editor in Supervision
• The configuration made with the Modbus Configurator can be stored as part of an usw file
• Breaker in Device page of APU 264 is updated correctly
• Older PPM-3 firmware no longer cause errors in USW 3
• Choosing the language to activate after doing translations also works with TCP-IP connection

3.30.1

07/12/2011

Changes:

• Supervision page is updated consistently according to active application.
• Batch read/write improved when offline.
• The correct access levels are applied for GC-1F.
• Edition of Energy counters improved.
• USW no longer claims exclusive access right to files.

3.30.0

08/11/2011

New features

• Support of the new controller AGC-4
• Counters: read-out of various counter values from the controller
• Identifiers: read-out of various id’s used the controller
• Dynamic M-Logic evaluation: the values for the M-Logic lines are evaluated on-the-fly
• AOP and M-Logic lines in use: provide an overview of where different event types are used in the logic lines
• Batch read: allows the read-out of logs and export to Excel file format
• Backup/restore: backup a controller for later restoring
• Translations: Prompt for selection of which language to set active after the writing of translations
• The language of the USW 3 application can be set to Russian
• Support for automatic reconnection after firmware flashing
• Display of all controller views at the same time
• A time offset used during synchronizing the time of the PC with the controller can be set
• Explicit scanning for available COM ports
• Emulation of a plant and response to e.g. inputs
• Deep dive allows to navigate between the upper and lower levels of option G7 based plants
• Permission: control which access levels can do what
• Display of the engine data retrieved over j1939 by the controller

Changes

• Only buttons and menus relevant for the offline situation are shown at startup of the USW 3
• During batch read/write the sequence of items is changed
• The help functionality has been updated with the new features listed below
• An issue regarding the sending of emails and/or SMS’s from the N-option is fixed
• In offline mode the Device page corresponding to a open file is shown
• User is prohibited to enter invalid IP address in the N-Option application
• Setting of the trending update rate is fixed
• The offline writing of view is no longer, mistakenly, reported as successful
• Logs: order of first two columns Timestamp and Text is switched so Timestamp goes first

3.21.0

15/04/2011

• New features
• AOP, Views and I/O Settings buttons in the top toolbar are active if connected to a device or an USW file with corresponding information is loaded.
• Support of GPU-3 REC
• Support of GC-1F ATS
• Support of AGC 222
• Support of various new parameters in PPM 3.05
• The application Modbus Configurator is added as part of the USW installation. This  application is used to perform a memory mapping to the configurable memory area in the devices.
• Application Settings: Functions to clear the settings that the USW saves from  session to session
• Option Wizard: Last entered customer information is displayed as default
• Project properties: Option- and hardware configuration can be copied to clipboard
• In Batch Read/Write a new shortcut, Ctrl-A, selects all items Changes
• Translations written from a Chinese PC: the issue, where the character "?" was  shown in GC-1F variants is fixed.
• Terminal numbers in the Inputs/Outputs page are corrected for AGC-3.
• Application Configuration is handled before Parameters during Batch Read/Write operations.
• Cyrillic K (К) handled properly
• Removal of “Generate random data”
• Supervision: “Engine data” was renamed to “Genset data”
• Writing of the netmask (AGC2xx products) is fixed.
• M-Logic dropdowns are always repopulated when connecting to another device type
• When logs are exported to Excel also the timestamps are saved in the file

3.20.0

04/02/2011

New features

• Support of the new product GC-1F/2
• Support of the new products APU-3, APU 264
• Move and copy items in M-Logic
• List of existing ports is displayed in communication setting popup
• Connectivity check in Supervision (require AGC firmware 3.6 and above)
• Compatibility check in Supervision (require AGC firmware 3.6 and above)
• Engine data in Supervision (require AGC firmware 3.6 and above)
• Cyrillic display option (CYD) shown in Options
• Terminal numbers shown in Input/Outputs
• Tooltip texts for parameters
• USW files can be shared among selected products series:
• AGC 212, 213, 232, 242, 243
• AGC 245, 246
• GC-1F and GC-1F/2
• List of keyboard shortcuts is extended
• Subnet mask can be edited for AGC 200 series if supported by product (require AGC firmware 3.6 and above)
• Device flashing and clock synchronization as part of the optional batch write steps.

Changes

• Improved scaling in the Device page of PPU-3, GPU-3, GPC-3, GPC-3 Hydro
• Updated Help functionality
• Installation on Windows 7 does not require administrative rights
• More intuitive tabing order in M-Logic
• Colour scheme editor and color scheme selection joined in the same popup
• Improved scaling of meters on Device page for GC-1F

3.16.0

24/08/2010

New features

• Import translations from file into selectable columns in Translations.
• Assign language names to translations columns.
• Change the sequence of the language columns in Translations.
• Copy language columns to other columns in Translations.
• Full 64 bit support:
• Signed USB driver for AGC 200 for 32 and 64 bit Windows platforms (XP, Vista and 7).
• Signed USB driver for AGC-3, PPM-3, PPU-3, GPU-3, GPC-3, GPU-3 Hydro for 32 and 64 bit Windows platforms (XP, Vista and 7)
• Drag-‘n-drop of USW file onto the USW application.
• Led or button number is shown in the header of the AOP item popup.
• User confirmation when writing AOP1, AOP2 or M-Logic.

Changes

• Updated Option wizard.
• Improved support of translations in AGC 200 series.
• Improved writing of translations.
• Improved support of Applications with a ring-shaped bus-bar.
• Improved error handling during writing of translations to GC-1F.
• Support of PPM 3.04.
• Support of new parameters for PPU-3, GPC-3, GPU-3, GPU-3 Hydro.
• Updated Help functionality.

3.15.1

07/05/2010

Changes (USW 3.15.1)

• Writing of M-Logic, AOP1 and AOP2 configurations are password protected.
• Enabled flags are written correctly when writing parameters.
• New features (USW 3.15.0)
• Support of AGC 200 variants which includes:
• Unicode text support in Translations
• Retrieval of logs
• Firmware upgrading
• Configuration of TCP/IP network parameters
• New USB driver
• Export of reports to PDF
• Support of voltage and power scaling in PPU3, GPU 3 and GPC 3
• M-Logic/AOP improvements:
• Color symbol to indicate the Enabled state of each line
• Optional user-defined description field for each line
• IP address edited in Settings dialog box through combobox with auto completion
• Plant Option dialog box: In offline mode the Product type is selected from a list of product families
• Batch Read/Write can be cancelled
• Save Application Configuration to jpeg file
• Installation file is digitally signed

Changes (USW 3.15.0)

• Increased Parameter writing speed
• Single DB application colored correctly
• Batch jobs: The caption shows whether it is a read or write batch job
• Improved export to Excel file format (content and format)
• Improved device filtering to prohibit writing of parameters from one device type to another
• Writing of M-Logic, AOP1 and AOP2 configurations are password protected
• Number of languages written in Translations cannot exceed the max allowed by the device
• Ring connected busbar is handled consistently

3.15.0

05/05/2010

New features

• Support of AGC 200 variants which includes:
• Unicode text support in Translations
• Retrieval of logs
• Firmware upgrading
• Configuration of TCP/IP network parameters
• New USB driver
• Export of reports to PDF
• Support of voltage and power scaling in PPU3, GPU 3 and GPC 3
• M-Logic/AOP improvements:
• Color symbol to indicate the Enabled state of each line
• Optional user-defined description field for each line
• IP address edited in Settings dialog box through combobox with auto completion
• Plant Option dialog box: In offline mode the Product type is selected from a list of product families
• Batch Read/Write can be cancelled
• Save Application Configuration to jpeg file
• Installation file is digitally signed

Changes

• Increased Parameter writing speed
• Single DB application colored correctly
• Batch jobs: The caption shows whether it is a read or write batch job
• Improved export to Excel file format (content and format)
• Improved device filtering to prohibit writing of parameters from one device type to another
• Writing of M-Logic, AOP1 and AOP2 configurations are password protected
• Number of languages written in Translations cannot exceed the max allowed by the device
• Ring connected busbar is handled consistently

3.14.0

28/12/2009

New features:

• Support of AGC 3.50
• Support of PPM 3.03
• Support of PPU 3.00.1 and its variants
• Support of New N-Option board (M1)
• M-Logic items collapsible/expandable
• Device ID visible on the status bar
• Connected device versus USW file compatibility check

Changes: 

• Dedicated GPU Hydro device overview
• Supervision legend improved
• Colour Scheme Editor in Supervision improved
• Improvements to Translations 
• Improved high alarm handling when using an older USW file
• N-option button only shown for supporting devices

3.13.0

15/10/2009

New features:

• Support of PPU3 and its variants.
• Search facility on the Parameters view.
• File association and distinctive icon for USW files.
• Dynamic legend on the Application Supervision view.
• Adjustable Polling delay for TCP-IP communication.

Changes:

• Performance boost in M-Logic loading.
• Parameters view improvements.
• Translations view: Extended Character dialog improved.
• Support of 20 configurable views in the AGC 3.4xx 
• Plant view for the gen-set mode “Mains Power Export” improved.

3.12.1

13/07/2009

Changes:

• Support of AGC 3.41

3.12.0

15/06/2009

New features: 

• Application configuration and Supervision works with up to 256 Gen-sets as supported by the G7 option in AGC 3.40 
• In Application Supervision three colors are used to indicate the state of the Gen-sets and bus-bars 
• Device IDs can be changed in Application Configuration 
• Support of TCP-IP Modbus communication through gateway to AGC or PPM without N-option card. 
• New command line parameter BATCHWRITE, which perform a batch write operation with the project file provided by the argument of the OPENFILE parameter 

Changes: 

• Enhancement of translations reading: Only available translations in the device are retrieved instead of all translations. 
• Printing an application configuration from the USW will no longer cause it to close. 
• When some multi-inputs are configured to digital inputs, their statuses are now updated in the Inputs/Outputs view. 
• Various fixes and enhancements in Trending. 
• Printing of translated strings is fixed. 
• The USW version is shown in the title bar 

3.11.1

24/03/2009

New features: 

• User-customizable Read/Write timeouts: The connection-settings dialog allows the end-user to adjust various read/write timeouts. 

Changes: 

• Support for PPM - 3.01.0. 
• If a firmware upgrade fails, it is not possible to repeat this operation when the display shows “BOOT MODE, FLASH ERASED” (this applies only to USW 3.11.0).

3.11.0

18/02/2009

New Features

• Improved PPM support 

Corrections

• Improvements in “Application configuration” 
• Modification of “Enable” and “High alarm” columns in the parameter list 
• Minor improvements to the plant view 
• Scaling of plant view instruments at high voltage values improved 
• Communication status improved 
• Trending improvements 

3.10.2

03/10/2008

New features:

• Added support for installation of new firmware for the AGC/PPM N-Options.

Changes:

• Improved stability of the Modbus TCP/IP interface.
• Max tags in the N-Option feature ‘Advanced logging’ changed to 48.

3.10.1

18/07/2008

New features:

• Clicking on the logo at the top of the navigation bar will bring you to our homepage
• Outputs A & B are now shown as explicit texts in the parameter window and the printout
• After synchronization of the translations, untranslated and already translated texts are clearly indicated

Changes:

• The commissioning panel is now active regardless of the value of the timer
• Writing a parameter file via a “batch write” will trigger a consistency check when appropriate

Corrections:

• Status when performing a “batch read” operation updated
• Two fail class groups could appear when configuring an AOP
• Button 2 on an AOP template was not aligned correctly
• Behavior of the translations synchronization updated
• Error message when leaving the translations window removed

3.10.0

30/06/2008

New features:

• Plant configuration and supervision (AGC 3.30)

Changes:

• Translation: Improvements in visualization and mask handling.
• Recently used file list handling updated.
• Placement of meters in AGC Dual main configuration adjusted.
• Input/Output window handling.

Corrections:

• Trending: Gain on some values adjusted.
• Data tracer: Handling of ‘Unit names’
• Firmware download recovery mode.

3.00.30

19/03/2008

•  Backward compatibility improved for ‘.usw’-files including languages.

3.00.29

05/03/2008

New features:

• Translations are now part of batch operations.
• Support of all fonts/charsets (Display unit european and cyrillic, graphical display european/cyrillic and limited european/chinese).
• Extended characters dialog redesigned.
• Font selection dialog added (graphical display only).
• Baud rate negociated with the unit (GC-1F only) up to 115200 bauds.
• Communication type shown on the status bar (serial COMx, TCP-IP IP: x.x.x.x).
• Application software/firmware file extension automatically selected according to the connected unit.

Corrections:

• Batch read/write: All AOP2s (ID 1 to 5) are readen/written instead of AOP2 ID 1 only.
• Parameters: When sending parameters stored in a project file, some parameter settings (configuration bits) could be overwritten in the unit.
• Parameters: Some items on the categories tab sheet could not be reached with mouse.
• Project file properties: Some hardware items could be duplicated.
• About window: Centered on the main monitor instead of the desktop (dual monitor systems).

3.00.27

11/10/2007

Correction:

• This USW release circumvents an issue present in the AGC firmware between release 3.10.2 and 3.21.0, where some parameters would not appear on the parameter list as expected.

3.00.26

20/09/2007

New features:

• The parameter inhibits are now shown on the parameter printout (only for parameters having inhibits defined).
• Parameter printout changed a bit (alternate colors).
• AOP1/2: Possibility to name individually leds and buttons (information saved in project file).

Changes:

• AOP1/2: Leds and buttons drawing changed slightly. M-Logic rule enabled -> white background. M-Logic rule not enabled -> hatched white background.
• Parameter filtering modified.

Corrections:

• When working on a saved parameter file (in a project file), and when editing a parameter, relays could appear as transducers.
• Faulty dependency check in I/O settings when working offline (information was based its dependencies on the device information).

3.00.25

13/07/2007

• List of the most recently used project files added.
• Writing of translations improved
• Offline configuration of the AOP-1 and -2 improved

3.00.24

26/06/2007

• Batch upload/download officially introduced (not in preview anymore).
• Save As feature
• Possibility to print all reports in A4 or Letter
• Option upgrade order form is now in english only
• AOP 1/2 printout refined
• Possibility to choose Modbus serial or TCP-IP
• Changes in the product database
• N-Option configurator

3.00.21

30/04/2007

• Changes for GC-1F.

3.0.0.20

23/02/2007

• Support of GC-1F product.

3.0.0.19

01/02/2007

• Support of the latest AGC release 3.1. 
• Usability of the parameter category filtering improved.
• Project file handling enhanced.
• Help file format changed.

3.0.0.18

17/10/2006

• First release

3.31.0

Changes

• Product updates: AGC-3, AGC 200, PPM-3, PPU-3, GPU-3, GPC-3, GPU-3 REC, GC-1F/2, AGC-4
• OEM options are removed from the Options page.
• OEM options are removed from the Option wizard.
• The user access level required for performing an update of the controller firmware of a GC- 1F is changed to "Customer".
• The keyboard shortcut “Alt+Tab” allows navigation back and forth between the USW and other  applications even when a popup is open
• Trending allows only realistic sample rates.

New features

• The Modbus Configurator (to set up the configurable memory area) is built into the USW
• Modbus configuration is included in the Batch Read/Write
• Notification sounds in case of alarms and batch operations.
• Custom logo can be used on printouts
• Broadcast progress is indicated in Application Configuration and Application Supervision (if supported by controller)
• New permission rule that prevents the user to see parameters that cannot be edited at  current access level