Multi-line 2 BGC Application Software series 1.x.

You’re about to download Multi-line 2 BGC Application Software series 1.x.

The software you are trying to download is obsolete. Please download the latest version from this page.

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

This software applies to the following DEIF products:

You’re about to download 1.10.3

The main changes implemented since the last version are as follows:

Changes:

  • Update of self-check functionality
Ver. Date Description

1.10.3

15/05/2015

Changes:

  • Update of self-check functionality

1.10.2

23/02/2007

Changes:

  • Menu for Voltage Trip (Phase-Phase or Phase-Neutral) removed.

1.10.1

21/02/2005

Changes:

  • Handling of MB in VDE0108 AUS mode updated.
  • Rampdown updated.
  • Returning from JUMP menu sets to main view.
  • Mode "Load take over" updated.
  • Digital input alarm handling updated.
  • Emergency stop default set to OFF.

1.10.0

07/02/2005

Changes:

  • Setting if WARNING fail class should autoreset or not added
  • Analogue input readings optimised for better precision
  • Alarm acknowledge updated for option VDE0108
  • Factory settings of var export/import changed
  • interface to USW regarding inputs optimised
  • Analogue input board (option M15) reading optimised
  • Test mode updated

1.05.0

05/01/2005

Changes:

  • When breaker position is unknown, breaker LED will be flashing red.
  • Now possible to open GB in Island SEMI when Loadshare not present and breaker alarms active.
  • Ramp down added to TEST mode.
  • GB opens immediately in MAN mode when activated.
  • RPM max. settings changed from 2000 to 4000. Overspeed alarms corrected according to this. Improved handling when using external power setpoint.
  • Password to changing password changed. Must use master password level to change master password. Must use OEM password level to change OEM password.
  • In VDE0108 alarm horn is now set off when first alarm of multiple alarms is acknowledged.
  • Display is updated when using binary input for alarm acknowledge

1.04.5

12/11/2004

Changes:

  • Governor and AVR offset function modified

1.04.4

19/10/2004

Changes:

  • Manual stop in AUTO mode is changed
  • Test mode handling changed
  • Handling of other languages than English is changed

1.04.2

01/09/2004

Changes:

  • Handling of mains breaker supervision when using contactor setting changed to avoid alarm when combined with zero-voltage coil trip of mains.

1.04.1

02/08/2004

Changes:

  • Gen-set will ramp up in TEST mode.
  • Underlined characters of extended ASCII-table added.

1.04.0

28/06/2004

Changes:

  • USW interface improved
  • Reset regulation functionality adjusted
  • Settings possibilities for Emergency stop-menu extended
  • Handling of GB and MB modified

1.03.1

09/03/2004

Changes:

  • Manufactor name for CAN-open option changed
  • Option H4 - minor chnnges
  • USW interface regarding GB and MB extended
  • Alarm inhibit functionality changed during stop-sequence
  • Short circuit protection functionality changed
  • Failclass 'Warning' functionality improved
  • Functionality of frequency and voltage acceptance detection changed
  • Check of language added to USW control
  • GSM option menu extended
  • Service timers functionality added to USW
  • Event log update functionality changed
  • GB feedback handling changed
  • Single running in Island-mode functionality changed
  • Running hour calculation improved

1.03.0

11/02/2004

New features:

  • Modeshift can now be controlled with digital input or menu 4440
  • Stop mode in menu 4900 added
  • Option for support of VDE0108 is added
  • GB position error can be deactivated (digital configurable input set to 'not used')
  • Kvarh (import / export) counter added
  • Sprinkler-mode functionality changed to include Short circuit 1,2
  • Start attempt counter added
  • New menu for number of sprinkler start attempt is added
  • 'Load take over'-mode added
  • Emergency power relay output added
  • Collective fault output added
  • 'Ready for operation' functionality added
  • Possibility for activation of Test mode with conf. digital input added
  • Possibility for 2 X option M13 or M14 added
  • SMS module updated with ID number in every message
  • SMS module updated with alarmbuffer, all alarms will now be sent
  • Modbus communication is optimised

Changes:

  • SMS module is stopped if no phone-numbers are used
  • CCM communication is optimised
  • W_L menu and functionality removed
  • Static charger menu and functionality removed
  • Voltage level for running detection changed
  • Timing changed, if modeshift is on and mains failure occur
  • 'Peak current' renamed for 'Short circuit'
  • H4 option shown in USW
  • If a mains fail occurs during TEST mode the AMF sequence will start
  • USW stop command optimised
  • Static sync improved function
  • Improved power factor calculation
  • Password handling optimised
  • Menu handling in regard to Option A1 A2 A3 optimised
  • Default setting for secondary value for current trafo's for Generator and busbar changed
  • Counter handling (hours, CB, MB operations) optimised
  • Deload is interrupted if remote start/stop is changed from start -> stop -> start
  • MB operations optimsed during change of configuration
  • Function of Relay 13 optimised
  • Menu handling in regard to loadshare PCB optimised
  • Menu handling for Option M13 optimised
  • Possibility for Test-mode in Island mode removed
  • Mains-failure detection improved
  • Start enables functionality improved
  • Log-functionality improved
  • Failclass handling in auto mode optimised

1.01.2

07/11/2003

Changes:

  • Security regarding write/erase operation in boot-sector is improved.

1.01.1

10/10/2003

Changes:

  • The 8 Start/stop menus are adjusted
  • Menu 4250, 'ID BAUD' -> 'TYPE' corrected

1.01.0

03/10/2003

New features:

  • Can-Open support enabled
  • 'JDEC' engine communication added

Changes:

  • Line 3 adjusted when 'mode button' is used
  • Eventlog secured when power up less than 3sec
  • Frequency measurement below 20Hz is disabled due to a problem under stopping the gen-set.  This could in rare cases generate a reset of the unit.
  • Timing in case of 'MB trip externt' adjusted

1.00.4

29/08/2003

Changes:

  • Changed max limit in menu 1290 1300 from 300% -> 350%
  • Changed text string for 2180 + 2190 (Deadband - > limit)
  • Removed PF control settings, not used

1.00.3

01/08/2003

New features:

  • Option H4 CCM Caterpiller

Changes:

  • SMS phonenumber-interface to USW adjusted
  • Peak-current measurement improved
  • dfdt and vector-jump function improved
  • Stop of gen-set if mains-fail is added
  • Energy counters added

1.00.2

01/07/2003

New features:

  • Possibility to configure input for Alarm Acknowledge added
  • Possibility to configure input for Alarm Inhibit added
  • Possibiblity for activating fuel-logic

Changes:

  • Close of MB in auto changed
  • Text changed: 'Sprinker' -> 'Fire pump'
  • Generator protection moved into Option C1
  • Display update sequence optimized
  • VDO-input for fuel-logic is optimized

1.00.0

30/06/2003

Initial release

On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).

Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.

DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.

DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.

Licence agreement for software downloaded from www.deif.com

Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.

The latest versions for full functionality

As always, we recommend that you install our offered improvements to fully utilise your DEIF product.

All improved software can be downloaded at your convenience at www.deif.com under “Software”.

Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.

Read more